It can be inserted in the HWIC slots of a Cisco 1841 Integrated Services Router (ISR) and Cisco 2800 and 3800 Series Integrated Services Routers or in the WAN interface card (WIC) slot of a Cisco IAD2430 Series Integrated Access Device to provide integrated DOCSIS connectivity in.

• The 4-port Cisco® EtherSwitch® 10/100 high-speed WAN interface cards (HWICs) HWIC-4ESW supported on the Cisco 1800 (modular)/1941, Cisco 2800/2900, and Cisco 3800/3900 series integrated services routers offer small-to-large-size businesses and enterprise branch office.
• Cisco CISCO1941/K9 1941 w/2 GE,2 EHWIC slots,256M (CISCO1941/K9) by Cisco. Price: $742.00 & FREE Shipping Cisco 1941 Integrated Services Router build on 25 years of Cisco innovation and product leadership. The new platforms are architected to enable the next phase of branch-office evolution, providing New & Used.

Cisco WAN :: 1941 ADSL Fail Over To 3G HWIC With IPSEC VPN

The setup is a S2S VPN with failover to 3G HWIC in a Cisco 1941 however the IPSEC tunnel needs to remain up through 3G if ADSL fails.The failover works ok, however when plugging ADSL back in, the - 'sh crypto session' shows both dialer 0, and dialer 1 with the crypto map session to the other side of the VPN and either side is now not pingable.The NoIP DDNS updater client runs on a server in the network and all IP resolution to host1,host2 works ok (other side of VPN is Cisco 1921 with ADSL HWIC and 3G HWIC). [code]

Cisco WAN :: 1921 / 1941 - Unable To See HWIC-1DSU-56K4?

We are currently moving from 1841 (EOL) to 1921/1941 routers. According to the module support doc [URL] this HWIC-1DSU-56K4 card is supported. We have tried both the 1921 and 1941 with the cards without any luck.
IOS Verison: c1900-universalk9-mz.SPA.152-1.T.bin
System Version: 15.0(1r)M9
Boot Error: %MAINBOARD-1-UNKNOWN_WIC: wic card in location 0/1 has an unknown id 0xB
Show Diag:
WIC Slot 1:
DSU 56K
WIC module not supported/disabled in this slot
Hardware revision 1.0 Board revision A0
[code].....

Cisco WAN :: 1941 Why Would CPU Usage Hover Around 45% Or So With One Machine Running Torrents

I am running a 1941 isr g2 router, which, according to my specs is equivalent to a cisco 3825 - which i also own.Why would the cpu usage hover around 45% or so with ONE machine running torrents? There is really no packet inspection etc...or anything else that would cause the cpu to work really hard...I am on a 100/5 connection.

Internet Kicks Off When Plug In Router

we have cable internet, the service has been going in and out for months now. Bought a new router still having problems. Cable company has been out several times, changed modem, etc. Now hooked up straight to cable with no router, working fine so far, but no wifi , kicks off when router is connected. In the past when router is on it will work for a few hours or even a day or two, then go out.

Ethernet Plug Connected To The Router?

Have got one ethernet plug connected to the router and then one upstairs connected to my ps3, can I add another plug and connect another device to it or do i need two plugs to connect to another port on my router for it to work? If I buy another set of plugs will they still work or will they cause interference?

Plug Wireless AP Into A Wired Router?

I have a router that was giver to me .I have a kinkle fire that I want to use from my home.I spent hours on the phone and someone @ ATT and some how the person gets lost when I ask them this questions.A total f 5 hours lost!

How To Make Modem Plug Into Switch Instead Of Router

I have a network set up currently with a cable modem that goes into a router, the router then goes to a 16 port switch and the switch goes to computers, printers, and my server. I am trying to figure out how to make the modem plug into the switch instead of the router. I'm guessing my problem lies with the default gateway since that is the router. Any suggestions on this? Or how is the best way to set this up? I have 2 NICs on my server and the server has windows 2008 r2.

Modem Doesn't Have A Ethernet Plug In For Router

My modem does not have a Ethernet plug in for my router. do I have to buy another modem for a 2nd computer?

Plug Wireless Router To Cable Modem?

How do I plug the wireless router to the cable modem?

Linksys Wireless Router :: WRT54G V1 Disconnect Power From Router For About 15 Seconds / Plug It Back In

I have a Linksys WRT54G2 v1 router which is having a daily problem of connectiing to the Internet on my home wireless LAN. My temporary solution is to disconnect the power from the router for about 15 seconds and plug it back in .... and all is well.... at least for another day or so.The real problem is that instead of properly connecting to IPv4 address 192.168.1.100 ..... it randomly connects to Autoconfiguration IPv4 address 169.254.29.54 When this problem occurs the SSID list shows both my 192 connection as well as a public network with no Internet connection?
I've used this router for several years without a problem until I recently bought a new Canon wireless MG5320 printer which initially had problems connecting to my LAN. After a telco with tech support the printer works fine but now I am now experiencing the Autoconfig address problem.My LAN consist of the WRT54G router, a Motorola cable modem, a Lenovo laptop running Win7 64bit, a Hp desktop running Win7 64bit and the Canon wireless printer. (all connected wirelessly)

Can Plug A Wireless Router Into A Hard Wired Router Port

can i use one of my hard wired router ports to plug in a wireless router and use them both?

Wireless :: No USB Port On Router To Plug Flash Drive?

My router does not have a usb port. So what now?

6867R - Network Cable Is Unplugged When Plug ADSL Line To Router?

I can connect to my router but not to Internet, it seams that ADSL line 'disconnects' my LAN/WLAN this issue is with Inalambrico 6867R router an other router, TP-Link is working great

Cisco WAN :: Difference Between HWIC-1ADSL-M And HWIC-1ADSL?

What is the difference between HWIC-1ADSL-M and HWIC-1ADSL without the '-M'?Can either of the above ADSL cards be used in Cisco 3845 router? We are using HWIC-1ADSL-M in our Cisco 3845 routers everywhere?

Linksys Wireless Router :: EA3500 Disconnect After Plug In Portable Hard Drive

I bought an EA 3500 refurbished through linksys. I can't configurate it using the CD-Rom. Always said 'can't find your router'. So I flash with the classic firmware, and it fixs the problem and automatically upgrade to smart Wi-Fi. That being said, whenever I plug in a portable hard drive, the router disconnect from internet after a minute. I tried my seagate HDD and also my flash driver. Both Lost internet after a minute or so. So I think it is probably the router's problem.

Cisco WAN :: Running All Switches Running By Default Configuration And Connected To WS-C4506

I have 30 switched in my corporate network it’s all up and running all switches running by default configuration and connected to WS-C4506 core switch our dhcp server pooling 192.168.100.1/27 network. Now we need to configure new Vlan for finance department this department has more than 200 users. If my server distributes 192.168.200.0 range ip can vlan2 automatically assign ip 200.0 addresses to finance department.All switches running default config no ip address assigned.

Cisco Firewall :: Configuration Migration From ASA 5540 Running 7.2 To 5525X Running 9.1

I need to replace an existing ASA 5540 with a new ASA 5525X. I would like to pre-stage and configure the new box with the existing config, migrate license and export certificate files before swapping it with the old one during a change window. The new firewall will run 9.1 on deployment. Now the same 7.2(4) cannot just be copied over to 5525X running the minimum 8.6 version. There is a Web based tool available at [URL] according to Cisco documentation but the page does not load for me (Cisco intranet only tool ?). Is there another tool for automatic conversion ?

Cisco WAN :: 2811 - Adding A HWIC In Router

I have a Cisco 2811 router with c2800nm-adventerprisek9_sna-mz.124-2.T6.bin as IOS and i wsh to install this HWIC 4port to increase available ports on my router. Wish to know if this is going to work,that is, if i installed it the IOS available will recognise this card

Cisco WAN :: Install HWIC-1GE-SFP On 3845 Router

In our Environmet we have 3845 Edge Router Current Ios Version is Version 12.4(1a),(c3845-advipservicesk9-mz.124-1a.bin)As management got another fiber leased line(Single Mode) for which i have install SFP slot part number HWIC-1GE-SFP,after installation of HWIC-1GE-SFP in router the follwing slot is showing
GigabitEthernet0/1/0
%HWIC_1GE_SFP-6-SFP_IN: Interface GigabitEthernet0/1/0 1000BaseLX SFP has been inserted
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/1/0 xx.xx.xx.xx. YES manual up down
for testing purpose i tried the same procedure into the switch and its working fine where as in Router the link is not coming up ,

Cisco WAN :: Configured New 2911 Router With HWIC-2T

We have configured new 2911 router with HWIC-2T with it.However we are seeing serial interfaces up, but can hardly ping other end. Again we are seeing a lot of CRC errors on serial interface.
But if we connected same cable, with other old router 2811, it works fine. Confiuration is same on both the routers. [code]

Cisco WAN :: Configuring HWIC-8A On 2911 Router?

I had purchased a HWIC-8A in an effort to provide terminal server capabilities into multiple routers. I had found a document that I thought would take me through the configuration but it doesn't appear that the command syntax is the same on the 2911's as it is in the document. Does any know how I would need to get this configured on the 2911 router?
Here is the document I was referencing
[URL]

Slap An HWIC - 4ESW Into A Router

meaning slap an HWIC-4ESW into a router, say, an 1841, create an ether channel out of them to connect to my switch?

Cisco WAN :: Can't Put A Second HWIC-4ESW In A 3825 Router And Don't Work

I put a second HWIC-4ES in a 3825 router and it does not work, only work the first card that is inserted, I use the slot 0 for it, the 0/0 and 1/0 work with serial card only if I put the HWIC-4ESW in this slots the router does not work, only work in 0/2 and 0/3 but only one, I need to know if there is a command to active it because the data sheet in CISCO indicate that this model of router support 2 HWIC-4ESW. url...

Cisco WAN :: Adding A HWIC 1FE Card To 2811 Router?

I have a 2811 router runnning IOS 12.4(21) and have added an HWIC 1FE card to slot 2. But the card doesnot show up in the router and all the three lights on the HWIC card is steady green. I have gone through some cisco documentation and found that i have to upgrade the IOS.
I have few questions before doing the upgrade.
1. Which IOS version should I upgrade to?
2. Will this erase my exisitng running configuration ? I have VPN services, PPPoATM, PBR etc.. all running on this router at present.
3. Presently i have a 128 MB CF card on the router. Will this be enough or do i need to upgrade this card also? Can i choose an IOS which will fit into this card otherwise while keeping all existng features?
4. I want to use the HWIC card for the ISP's internet service through PPPoE. Will this be possible with the upgraded IOS ?

Cisco WAN :: Router 2811 Can't Detect HWIC-2FE Card?

I am trying to connect HWIC-2FE Card to my Cisco 2811 Router. The router is unable to detect the card. I get the following error message:
' %GT96K_FEWAN-1-UNKNOWN_WIC: NM slot 0, wic card has an unknown id 53BPort Statistics for unclassified packets is not turned on.'

Cisco WAN :: Which Type Of HWIC Card Should Use In 2911-sec / K9 Router

I have cisco 2611 + NM1E , and i want to trade in for a cisco 2911 security router + HWIC4 Card.Which type of HWIC card should i use in the cisco2911-sec/k9 router?

Cisco 1941 Hwic Slots Download

Cisco WAN :: HWIC-2CE1T1-PRI Not Supported On 2801 Router?

Cisco 1941 Hwic Slots Igt

The HWIC-2CE1T1-PRI card isn't supported on a CISCO2801 router

Cisco WAN :: HWIC-3G-CDMA-S - Can't Access Router From Internet

The problem is I can't access the router from the internet. I am also an ocean away from the site. I have an ugly hack set up where I access an inside PC with Teamviewer and then puTTy to the router, but it is slow, ugly, and doesn't fix my problem. I need to be able to set up internet accessible servers at this location for VOIP, VPN, and REAL remote access.Everything else works fine. Connection is stable. Speed is kinda ******, but that's not so important.
First off some specs:Cisco 2801c2801-ipvoicek9-mz.124-24.T1.binhwic-3g-cdma-sSprint 3G data plan
Ok, I have set up the previous equipment as a router for a branch office where 3G access is the only available internet access.I have had the excruciating experience of talking with Sprint Tech Support, and would rather shoot myself in the foot than do so again.
Here is what they told me: 'They block ports, but they can't tell me which ones.'Here is relevant info I have been able to gather.The IP connection the ISP gives us is not NATTED. That is the address at wimi.com and show int dialer 0 is the same one.Most forums say Sprint only blocks port 80.Zenmap (nmap for windows) says the router has NO open ports but DOES exist.Router does not respond to pingsCan't SSH into router from internetCan't access a test local server with port 8080 or 8081 open with the correct nat statement in Cisco routerNo filtering access-list for testing The config should be just fine as a base config for using hwic-3g-cdma-s as the main internet access interface for a router. Everything works fine aside from the lack of remote access.
So in my head it has to be one of 3 problems.
1. The card is doing some weird stuff to incoming requests
2. Sprint is blocking WAN requests on port 22, 2200, 8080, and 8081 and pings (tested). Maybe they block all WAN requests?
3. There is something wrong with my config.
why I can't remote access into my router or things to try with the config?
Below are some config pastes:
chat-script cdma ' 'ATDT#777' TIMEOUT 60 'CONNECT'
!
ip ssh authentication-retries 2
ip ssh port 2200 rotary 1
ip ssh version 2
[code]....

Cisco Infrastructure :: Connect Two Router With One HWIC-4ESW Card?

How Can I connect two router with one HWIC-4ESW card , I have Problem with this because when I tried to do , I received the message I can´t configure IP address on L2. The idea is to connect two routers with /30.

Cisco Switching/Routing :: Not Detecting HWIC-2T In 1921 Router?

I Have installed HWIC-2T card in my cisco 1921 router but it is not able to detected in router. find the ver of router
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL] Copyright (c) 1986-2012 by Cisco Systems, Inc.Compiled Tue 20-Mar-12
[Code]......

Cisco WAN :: Apply MQC On 4 Port HWIC-4ESW - 3845 Router?

I have 3845 Router with HWIC-4ESW & I am trying to apply MQC on SVI interface but I keep getting configuration Error!-RTR(config-if)#service-policy output XYZ_WAN_QOS Configuration failed I believe that HWIC-4ESW is Layer 2 port & you can not apply Module Qos on SVI interface. I am exploring other option.
I have following link for 1 OR 2 Port Fast Ethernet port but not sure whether this will support what I am looking for.[URL] Aslo I have HWIC-1GE-SFP card on Same router where MQC works fine .interface GigabitEthernet0/1 description METRO-E duplex auto speed auto media-type rj45 service-policy output Metro-E?

Cisco 1941 Hwic Slots 777

Cisco WAN :: 2821 Router / Card Hwic-D-9ESW - Cannot Ping To Interface

Cisco 1941 Hwic Slots Coin

I have some issue on Card Hwic-D-9ESW with Router 2821, i was install card 9ESW in to router 2821 on slot 2 and 3. After I show run, the Cisco Router 2821 have interface F0/3/0 - F0/3/8.and i configure V lan already and interface up also.
When i connect PC to port F0/3/0, the interface is up, but i cannot pint go interface, i mean it request time out. My question is, Is it correct that i install card into slot 2 and 3?
What is the problem all port up but i cannot ping to interface?
Note: the same V lan